BENDIX BW2212 Manual de usuario

1SD-19-516014567891023Item No. Description Qty.1 IR Camera 12 IR Camera Bracket 13 IR Camera Harness 14 Mounting Bracket 15 Display 16 Combiner 17 25-

10SERVICING THE XVISION SYSTEMThe following sections provide instructions for maintaining and/or replacing components of the XVision system.CAMERA MOU

11 7. Verify that the mounting bracket is level. If it is not, use the shims included in the mounting bracket kit. 8. Apply sealant between all co

12FIGURE 22 - FULLY ASSEMBLED IR CAMERAAiming AssemblyAttach the IR camera to the IR camera bracket13. Position the IR camera onto the factory-instal

13Replacing the Aiming Adjusters1. Unlock the IR camera by turning the two IR camera aiming adjusters and the IR camera standoff 1/4 turn countercl

14Bezel Retaining PlugFIGURE 26 - IR CAMERA WINDOW AND BEZEL RETAINING PLUGIR CameraIR Camera WindowIR Camera Win-dow SealBezel Heater As-semblyIR CA

15IR CAMERA WINDOW HEATER REPLACEMENT 1. Unlock the IR camera by turning the two IR camera aiming adjusters and the IR camera standoff 1/4 turn co

16DISPLAYMaintaining the Combiner MirrorThe combiner is a sensitive optical element and should be cleaned when it becomes dirty or lled with debris.

17Display Bracket Replacement - CB Style Mount (Overhead)Refer to CB Style Mount (Dashboard) procedure.Display Bracket Replacement - Friction Hinge

18Display Replacement IMPORTANT: The display is not waterproof and should not be exposed to rain, snow, or moisture. Under extreme conditions, water

1921. Loosely install the harness tie-wrap around the harness.22. Position the IR camera onto the factory-installed aiming assemblies. Refer to Figu

2SAFE MAINTENANCE PRACTICES . . . . . . . . . 3INTRODUCTION. . . . . . . . . . . . . . . . . . . . 3COMPONENTS . . . . . . . . . . . . . . . . .

20BatteryHeadlampHeadlampSwitch1 AMP fastopen fuseIgnitionSwitch3 AMP slowopen fuseBlackWireBlueWireRedWireACBIgnitionbusGroundBusButtSplice27. Re-in

21FIGURE 38 - IR CAMERA AIMED CORRECTLY AIMING THE IR CAMERAThe aiming adjusters on the IR camera bracket allow the forward eld of view (FOV) of the

22 NOTE: Do not tamper with or adjust any factory-installed screws while aiming the camera. Only turn the vertical aiming adjuster. FIGURE 39 - VE

23FIGURE 43 - ELECTRICAL WIRING DIAGRAM FOR BENDIX® XVISION® NIGHT VISION SYSTEM

24TROUBLESHOOTINGTroubleshooting Your Bendix® XVision® Night Vision System Situation Possible SolutionsNo image on the display. Bendix logo does not

25 Situation Possible SolutionsIR camera image is not displayed after the Bendix logo fades away on the display.Wait two minutes after the Bendix®

26NOTES

27NOTES

28BW2212 © 2011 Bendix Commercial Vehicle Systems LLC. All Rights Reserved. 8/11 Printed in U.S.A.

3SAFE MAINTENANCE PRACTICES WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS TO AVOID PERSONAL INJURY OR DEATH:When working on or around a vehicle,

4CB STYLE MOUNTING KIT (PIECE NO. 5010081)The CB style mounting kit contains the necessary mounting hardware for the CB style dashboard option and CB

5Knob kit (service piece no. 5010247) – The knob kit includes four 1/4 in. at washers and two 1/4-20 threaded knobs, which are installed onto both s

6HARNESS KIT (PIECE NO. 5010083)The harness kit includes:IR Camera Harness (piece no. 5010246, service piece no. 801156) – The IR camera harness is ap

7Vehicle Harness (piece no. 5010260, service piece no. 801157) – The vehicle harness is approximately 12 feet long and provides power to the Bendix®

8AIMING ADJUSTER TOOLThe aiming adjuster tool is included with the Bendix® XVision® Night Vision System kit, but cannot be ordered individually. It is

9REPLACEMENT KITSThe following five kits contain replacement parts for the Bendix® XVision® Night Vision System. Each of the replacement kits can be o